Overview and Key Concepts
The source is used to create the flow items that travel through a model. Each source creates one class of flow item and can then assign properties such as labels or color to the flow item it creates. Sources can create flow item per an inter-arrival rate, per a scheduled arrival list, or simply from a defined arrival sequence.
The source is a fixed resource, although it does not receive flow items. Instead it creates the flow items and releases them. For that reason, it has no Input properties.
The source can operate in one of three possible modes:
- Inter-Arrivaltime Mode: In inter-arrivaltime mode, the source uses its inter-arrivaltime function. This function's return value is the time to wait till the next arrival of a flow item. The source waits this amount of time, then creates a flow item and releases it. Once the flow item has exited, it calls the inter-arrivaltime function again and repeats the cycle. Note that the inter-arrivaltime is defined as the time between the exit of one item and arrival of the next item, not as the time between the arrival of one item and the arrival of the next item. If you would like to make the inter-arrivaltime be defined as the true time between arrivals, then use a downstream queue with a large capacity to make sure that the source immediately sends on flow items when they are created. You can also specify whether the inter-arrivaltime should be executed for the first arrival, or if the first flow item should be created at time 0.
- Arrival Schedule Mode: In arrival schedule mode, the source follows a schedule defined by the user in the schedule table. Each row of the table specifies an arrival of flow item(s) at a given time in the simulation. For each arrival entry, you can specify the arrival time, name, number of items to create, and additional item labels for that arrival. The arrival times should be ordered correctly in the schedule table, meaning each entry's arrival time should be greater than or equal to the previous entry's arrival time. If the source is set to repeat the schedule, then it will immediately loop back on the first arrival after the last arrival, causing the first entry's arrival to happen at the exact same time as the last entry's arrival. Note here that, when repeating the schedule, the first entry's arrival time only applies to the very first loop through the schedule. This allows you to have an initial arrival time that is executed once, but not repeated. If you would like the source to wait a given amount of time between the last arrival and the repeated first arrival, then add an extra entry to the end of the table, give it an arrival time greater than the previous entry's arrival time, but have 0 flow item arrive for that new entry.
- Arrival Sequence Mode: Arrival sequence mode is like arrival schedule mode, except that there is no time associated with the arrivals. The source will create the flow item for a given table row, and then as soon as the last flow item for that entry has exited, it will immediately go to the next row in the table. You can also repeat the arrival sequence.
For information on events, see the Event Listening page.
The source uses the standard events that are common to all fixed resources. See Fixed Resources - Events for an explanation of these events.
The source has the following additional events:
This event occurs once for each flow item at the time the item is created. The item is created inside the source, but without triggering the On Entry event. This is the first opportunity to get a reference to the created item. Any labels defined in columns in the Arrivals table have not yet been added to the item at this point. This event is immediately followed by the On Exit event unless the item's release is delayed by a downstream object.
It has the following parameters:
|A reference to the flow item created by the source.
|The row number of the row in the Arrivals table where this arrival was defined. This will be 0 when using the Inter-Arrival Time Mode.
Inter Arrival Time
This event only fires if the source's Arrival Style is set to Inter-Arrival Time. This event once for each flow item that is created. The inter arrival time event is fired immediately after the On Reset of the source and immediately before each On Exit event.
This event has no parameters.
The return value of the Inter-Arrival Time field is a number which is the model time until the next flow item is created.
For statistical purposes, the source will be in one of the following states at various points during a simulation run. The current state can be viewed by clicking on the object and then viewing the Statistics panel in Properties.
There are no flow items in the source. It is waiting until its next creation event to create flow item.
Flow items have been created and are waiting to leave the source.
The source tracks the following statistics. These can be viewed by clicking on the object and then viewing the Statistics panel in Properties.
The total number of items that have exited the source.
If the source is blocked and items cannot immediately exit the source when they are created, the time the item remains in the source before exiting will be recorded.
The Source object uses the following properties panels:
The Source object shares several properties with all fixed resources:
Additionally, the Source object uses the following properties: